Weg Industrial Grade 7.5hp 1-phase 215t Compressor Duty Electric Motor 1760 RPM

  
FULL INDUSTRIAL GRADE 7.5 HP - 1 PHASE - 213T / 215T FRAME - 1760 RPM - 230VAC - 1 3/8 SHAFT DIAMETER. ELECTRIC MOTOR FOR BELT DRIVEN AIR COMPRESSORS. THIS MOTOR ROTATES CCW (COUNTER CLOCK WISE) WHEN VIEWED FROM SHAFT END.

CONTINUOUS RUN COMPRESSOR DUTY MOTOR. ODP (OPEN DRIP PROOF FOR DRY INDOOR ENVIRONMENTS). 31.3 AMPS AT 230VAC, 40AMP MAGNETIC STARTER IS REQUIRED TO EFFICIENTLY START AND PROVIDE PROPER MOTOR PROTECTION, PROFESSIONAL INSTALLATION REQUIRED. FOR DIMENSIONAL DATA, PLEASE SEE OUR ATTACHED PICS.

WHY YOU ALWAYS NEED A MAGNETIC STARTER ON INDUSTRIAL GRADE ELECTRIC MOTORS FOR AIR COMPRESSORS. A MAGNETIC STARTER IS ALWAYS REQUIRED ON ANY 184T FRAME MOTOR AND LARGER. WIRING AN INDUSTRIAL SIZE MOTOR THROUGH THE PRESSURE SWITCH ALONE, IS NEVER A GOOD IDEA, AND HERE'S WHY. PRESSURE SWITCHES DO NOT COME WITH OVERLOAD PROTECTION FROM POWER SURGE OR LIGHTING.

IN ADDITION, PRESSURE SWITCHES HAVE VERY SMALL CONTACT POINTS THAT CONNECT TO THE MOTOR. SMALL CONTACT POINTS CAN STARVE YOUR MOTOR OF THE NECESSARY POWER IT REQUIRES TO START AND RUN NORMALLY. MAGNETIC STARTERS NOT ONLY PROVIDE YOU WITH MOTOR PROTECTION FROM POWER SURGE AND LIGHTING, THEY ALSO HAVE LARGER CONTACT POINTS THAT CONNECT TO YOUR ELECTRIC MOTOR. ALLOWING FOR A STEADY FLOW OF CURRENT THAT AN INDUSTRIAL GRADE MOTOR REQUIRES TO RUN AND ESPECIALLY START UP.

BY INCORPORATING A MAGNETIC STARTER WILL ALLOW YOUR MOTOR TO LAST MUCH MUCH LONGER. Amperage: 31.3 FLA (FULL LOAD AMPS) AT 230V. Service Factor Amperage: 35.5 SFA.

Phase: One / Single Phase. Voltage : 208 - 230VAC (NOT SUITED FOR INCOMING VOLTAGE THAT IS BELOW 208V). Frame: 213/5T (213T / 215T). Shaft Diameter: 1 3/8 Keyed shaft. Shaft Length: 3.30 SHAFT LENGTH. Rotation: CCW WHEN VIEWED FROM SHAFT END (THIS MOTOR IS NOT REVERSIBLE). Enclosure: ODP / Open Drip Proof (FOR USE IN DRY INDOOR ENVIRONMENTS). WIRING SCHEMATIC FOR 230V SHOWN ON ATTACHED PIC OF MOTOR NAMEPLATE. We would be more than happy to correct any issue. Regardless if we accidentally sent you the wrong item (which seldom happens) or the customer ordered the wrong part by mistake. WE WILL correct any potential problem. Liability: UPE_Group is a dstributor and as such, has no direct or indirect control over the materials, processes, or quality control procedures used by the manufacturers of the products we resell. Accordingly, UPE_Group will NOT be held responsible for damages resulting from product defects, or, from mis-applications/improper installations by the customer or end user. It is the purchasers responsibility to determine the suitability of the product for the specific application.

If it is deemed defective, UPE_Group shall be held harmless of any and all damages including (but not limited to) physical injury, property damage, water damage or otherwise for any reason. It is the purchasers responsiblity to determine the suitability of these products for your specific application. Including, but not limited to, using alternative products. UPE_Group shall be held harmless of any and all damages including but not limited to physical, property, water or otherwise for any reason. Your use of any information or materials on this listing is entirely at your own risk, for which we shall not be liable.

By submitting your order, the purchaser acknoledges agreement with the Terms & Conditions as outlined here and our website. The item "WEG INDUSTRIAL GRADE 7.5HP 1-PHASE 215T COMPRESSOR DUTY ELECTRIC MOTOR 1760 RPM" is in sale since Monday, May 14, 2018.

This item is in the category "Business & Industrial\Industrial Automation & Motion Controls\Electric Motors\General Purpose Motors". The seller is "upe_group" and is located in Dallas, Georgia. This item can be shipped to United States, Philippines, Cayman islands.

1. Enclosure Type: ODP (Open Drip-Proof)
2. Insulation Class: F (Max 311°F)
3. Model: 00718OS1CCD215T
4. Country/Region of Manufacture: Brazil
5. MPN: 00718OS1CCD215T
6. Rated/Full-Load Torque: 22.1 FT LBS
7. NEMA Design Letter: Design B (General Purpose)
8. Mounting Type: TERMINAL BOX LOCATED LEFT SIDE FROM SE
9. Shaft Diameter: 1 3/8 in
10. Starting/Locked Rotor Torque: 220%
11. Full Load Amps: 33.8 @ 208V / 32.2 @ 230V
12. Type: COMPRESSOR DUTY MOTOR
13. Rated Load (HP): 7.5
14. Power Source: AC
15. NEMA Frame Suffix: 213T / 215T
16. AC Frequency Rating: 60 Hz
17. Current Type: AC
18. Special Motor Construction: COMPRESSOR DUTY / GENERAL PURPOSE
19. Brand: WEG
20. Nominal Rated Input Voltage: 230V
21. California Prop 65 Warning: WARNING: Some parts of this product contain chemicals, including Cobalt known to the state of California to cause cancer, birth defects and other reproductive harm.
22. Reversible/Non-Reversible: NON-REVERSIBLE / CCW SE
23. Service Factor: 1.15
24. Actual Rated Input Voltage: 230V
25. AC Phase: Single Phase
26. Shaft Type: Keyed
27. Base RPM: 1760