THIS IS AN OPEN DRIP PROOF MOTOR AND IS INTENDED TO BE USED IN DRY, NON-DUSTY INDOOR ENVIRONMENTS. BALDOR COMPRESSOR DUTY MOTORS ARE SPECIFICALLY DESIGNED TO MEET START UP AND TORQUE REQUIREMENTS FOR INDUSTRIAL GRADE AIR COMPRESSOR PUMPS.
BALDOR MOTORS ARE RATED HEAVY DUTY, FULL INDUSTRIAL AND DESIGNED TO LAST. THIS MOTOR IS MADE IN THE USA. PLEASE MAKE SURE THE ELECTRIC MOTOR YOU ARE REPLACING MATCHES THE SPECS SHOW N BELOW BASED ON YOUR EXISTING MOTORS DATA PLATE. WHY YOU ALWAYS NEED A MAGNETIC STARTER ON INDUSTRIAL GRADE ELECTRIC MOTORS FOR AIR COMPRESSORS. A MAGNETIC STARTER IS ALWAYS REQUIRED ON ANY 184T FRAME MOTOR AND LARGER.
WIRING AN INDUSTRIAL SIZE MOTOR THROUGH THE PRESSURE SWITCH ALONE, IS NEVER A GOOD IDEA, AND HERE'S WHY. PRESSURE SWITCHES DO NOT COME WITH OVERLOAD PROTECTION FROM POWER SURGE OR LIGHTING. IN ADDITION, PRESSURE SWITCHES HAVE VERY SMALL CONTACT POINTS THAT CONNECT TO THE MOTOR. SMALL CONTACT POINTS CAN STARVE YOUR MOTOR OF THE NECESSARY POWER IT REQUIRES TO START AND RUN NORMALLY.
MAGNETIC STARTERS NOT ONLY PROVIDE YOU WITH MOTOR PROTECTION FROM POWER SURGE AND LIGHTING, THEY ALSO HAVE LARGER CONTACT POINTS THAT CONNECT TO YOUR ELECTRIC MOTOR. ALLOWING FOR A STEADY FLOW OF CURRENT THAT AN INDUSTRIAL GRADE MOTOR REQUIRES TO RUN AND ESPECIALLY START UP.
BY INCORPORATING A MAGNETIC STARTER WILL ALLOW YOUR MOTOR TO LAST MUCH MUCH LONGER. 5HP - 184T FRAME - 1750 RPM - 208-230 VOLT - 1-1/8" SHAFT DIAMETER - 3.5" SHAFT LENGTH - 1.25 SERVICE FACTOR - ODP (OPEN DRIP PROOF) ENCLOSURE. THIS BALDOR SPEC MOTOR IS A DIRECT REPLACEMENT OF THE L1410T. VOLTAGE: 208-230V THIS MOTOR IS NOT DESIGNED TO HANDLE INCOMING VOLTAGE LESS THAN 208V.
SHAFT DIAMETER: 1-1/8 KEYED SHAFT. ROTATION: REVERSIBLE CW OR CCW ROTATION. ENCLOSURE: ODP OPEN DRIP PROOF. We would be more than happy to correct any issue.Regardless if we accidentally sent you the wrong item (which seldom happens) or the customer ordered the wrong part by mistake. WE WILL correct any potential problem.
Liability: UPE_Group is a dstributor and as such, has no direct or indirect control over the materials, processes, or quality control procedures used by the manufacturers of the products we resell. Accordingly, UPE_Group will NOT be held responsible for damages resulting from product defects, or, from mis-applications/improper installations by the customer or end user. It is the purchasers responsibility to determine the suitability of the product for the specific application.
If it is deemed defective, UPE_Group shall be held harmless of any and all damages including (but not limited to) physical injury, property damage, water damage or otherwise for any reason. It is the purchasers responsiblity to determine the suitability of these products for your specific application. Including, but not limited to, using alternative products.
UPE_Group shall be held harmless of any and all damages including but not limited to physical, property, water or otherwise for any reason. Your use of any information or materials on this listing is entirely at your own risk, for which we shall not be liable. By submitting your order, the purchaser acknoledges agreement with the Terms & Conditions as outlined here and our website.
The item "5HP BALDOR COMPRESSOR DUTY INDUSTRIAL ELECTRIC MOTOR, 184T, 1750 RPM, 208-230V" is in sale since Monday, June 24, 2019. This item is in the category "Business & Industrial\Industrial Automation & Motion Controls\Electric Motors\General Purpose Motors". The seller is "upe_group" and is located in Metro Atlanta GA.
This item can be shipped to United States, Philippines, Cayman islands.